Outputs (40)

Integrating user-centred design in the development of a silent speech interface based on permanent magnetic articulography (2015)
Book Chapter
Cheah, L. A., Gilbert, J. M., Gonzalez, J. A., Bai, J., Ell, S. R., Fagan, M. J., Moore, R. K., Green, P. D., & Rychenko, S. I. (2015). Integrating user-centred design in the development of a silent speech interface based on permanent magnetic articulography. In Biomedical Engineering Systems and Technologies; Communications in Computer and Information Science (324-337). Springer Verlag. https://doi.org/10.1007/978-3-319-27707-3_20

Abstract: A new wearable silent speech interface (SSI) based on Permanent Magnetic Articulography (PMA) was developed with the involvement of end users in the design process. Hence, desirable features such as appearance, port-ability, ease of use and... Read More about Integrating user-centred design in the development of a silent speech interface based on permanent magnetic articulography.

Effect of ultrasonic melt treatment on the refinement of primary Al3Ti intermetallic in an Al–0.4Ti alloy (2015)
Journal Article
Mi, J., Connolley, T., Eskin, D., & Wang, F. (2016). Effect of ultrasonic melt treatment on the refinement of primary Al3Ti intermetallic in an Al–0.4Ti alloy. Journal of Crystal Growth, 435, 24-30. https://doi.org/10.1016/j.jcrysgro.2015.11.034

High intensity ultrasonic melt treatment was applied to an Al–0.4 wt% Ti alloy over three selected temperature ranges: 810 to 770 °C (above liquidus), 770 to 730 °C (across liquidus), and 730 to 690 °C (below liquidus). The size and morphology of the... Read More about Effect of ultrasonic melt treatment on the refinement of primary Al3Ti intermetallic in an Al–0.4Ti alloy.

Optimal operation of MEA-based post-combustion carbon capture for natural gas combined cycle power plants under different market conditions (2015)
Journal Article
Luo, X., & Wang, M. (2016). Optimal operation of MEA-based post-combustion carbon capture for natural gas combined cycle power plants under different market conditions. International journal of greenhouse gas control, 48(Part 2), 312-320. https://doi.org/10.1016/j.ijggc.2015.11.014

Carbon capture for fossil fuel power generation attracts an increasing attention in order to address the significant challenge of global climate change. This study aims to explore the optimal operation under different market conditions for an assumed... Read More about Optimal operation of MEA-based post-combustion carbon capture for natural gas combined cycle power plants under different market conditions.

Design optimization of TBM disc cutters for different geological conditions (2015)
Journal Article
Xia, Y., Zhang, K., & Liu, J. (2015). Design optimization of TBM disc cutters for different geological conditions. World Journal of Engineering and Technology, 3(4), 218-231. https://doi.org/10.4236/wjet.2015.34023

A novel optimization methodology for the disc cutter designs of tunnel boring machines (TBM) was presented. To fully understand the characteristics and performance of TBM cutters, a comprehensive list of performance parameters were investigated, incl... Read More about Design optimization of TBM disc cutters for different geological conditions.

Modelling and experimental study of the spray forming of dissimilar metals (2015)
Thesis
Lee, T. L. Modelling and experimental study of the spray forming of dissimilar metals. (Thesis). University of Hull. https://hull-repository.worktribe.com/output/4218236

This research describes a systematic study to develop a strong interfacial bond in as-sprayed dissimilar metallic alloys. Non-destructive three-dimensional microstructure and residual stress characterisations via X-ray micro-computed tomography and n... Read More about Modelling and experimental study of the spray forming of dissimilar metals.

Noise control of dipole source by using micro-perforated panel housing (2015)
Journal Article
Xi, Q., Choy, Y. S., Cheng, L., & Tang, S. K. (2016). Noise control of dipole source by using micro-perforated panel housing. Journal of Sound and Vibration, 362, 39-55. https://doi.org/10.1016/j.jsv.2015.09.047

Mitigating low-frequency noise in a small ducted fan system such as hairdryer is still a technical challenge. Traditional duct lining with porous materials work ineffectively due to the limitation of its thickness and length of small domestic product... Read More about Noise control of dipole source by using micro-perforated panel housing.

Estimation of local anisotropy of plexiform bone: Comparison between depth sensing micro-indentation and Reference Point Indentation (2015)
Journal Article
Dall'Ara, E., Grabowski, P., Zioupos, P., & Viceconti, M. (2015). Estimation of local anisotropy of plexiform bone: Comparison between depth sensing micro-indentation and Reference Point Indentation. Journal of biomechanics, 48(15), 4073-4080. https://doi.org/10.1016/j.jbiomech.2015.10.001

The recently developed Reference Point Indentation (RPI) allows the measurements of bone properties at the tissue level in vivo. The goal of this study was to compare the local anisotropic behaviour of bovine plexiform bone measured with depth sensin... Read More about Estimation of local anisotropy of plexiform bone: Comparison between depth sensing micro-indentation and Reference Point Indentation.

The micro-architecture of human cancellous bone from fracture neck of femur patients in relation to the structural integrity and fracture toughness of the tissue (2015)
Journal Article
Greenwood, C., Clement, J. G., Dicken, A. J., Evans, J. P., Lyburn, I. D., Martin, R. M., Rogers, K. D., Stone, N., Adams, G., & Zioupos, P. (2015). The micro-architecture of human cancellous bone from fracture neck of femur patients in relation to the structural integrity and fracture toughness of the tissue. Bone Reports, 3, 67-75. https://doi.org/10.1016/j.bonr.2015.10.001

Osteoporosis is clinically assessed from bone mineral density measurements using dual energy X-ray absorption (DXA). However, these measurements do not always provide an accurate fracture prediction, arguably because DXA does not grapple with 'bone q... Read More about The micro-architecture of human cancellous bone from fracture neck of femur patients in relation to the structural integrity and fracture toughness of the tissue.

Towards optimisation of load-time conditions for producing viscoelastically prestressed polymeric matrix composites (2015)
Journal Article
Fancey, K. S., & Wang, B. (2016). Towards optimisation of load-time conditions for producing viscoelastically prestressed polymeric matrix composites. Composites. Part B, Engineering, 87, 336-342. https://doi.org/10.1016/j.compositesb.2015.09.003

A viscoelastically prestressed polymeric matrix composite (VPPMC) is produced by applying a tensile creep load to polymeric fibres, the load being released before the fibres are moulded into a polymeric matrix. The viscoelastically recovering fibres... Read More about Towards optimisation of load-time conditions for producing viscoelastically prestressed polymeric matrix composites.

In situ synchrotron X-ray studies of the coupled effects of thermal and solutal supercoolings on the instability of dendrite growth (2015)
Journal Article
Li, F., Zhang, J., Dong, Q., Dai, Y., Fu, Y., Xie, H., Mi, J., Yin, F., & Sun, B. (2015). In situ synchrotron X-ray studies of the coupled effects of thermal and solutal supercoolings on the instability of dendrite growth. Materials Characterization, 109, 9-18. https://doi.org/10.1016/j.matchar.2015.09.008

© 2015 Elsevier Inc. All rights reserved. Special growth pattern representing unique growth conditions is a vital clue to investigate the morphology evolution mechanism in metallic alloy solidification. The dendrite pattern and growth orientation of... Read More about In situ synchrotron X-ray studies of the coupled effects of thermal and solutal supercoolings on the instability of dendrite growth.