Skip to main content

Research Repository

Advanced Search

Outputs (30)

Incorporation of inorganic carbon nanotubes fillers into the CA polymeric matrix for improvement in CO2/N2 separation (2015)
Journal Article
Jawad, Z. A., Ahmad, A. L., Low, S. C., & Zein, S. H. (2015). Incorporation of inorganic carbon nanotubes fillers into the CA polymeric matrix for improvement in CO2/N2 separation. Current nanoscience, 11(1), 69-79. https://doi.org/10.2174/1573413710666140922224633

Among all separation techniques, membrane technology has been shown to reduce CO 2 emissions without any phase changes due to its rapid, energy efficient process. The membrane-based gas separation must consist of a defect-free, thin, dense skin layer... Read More about Incorporation of inorganic carbon nanotubes fillers into the CA polymeric matrix for improvement in CO2/N2 separation.

A novel sensor based on electropolymerized substituted-phenols for pH detection in unbuffered systems (2015)
Journal Article
Dai, C., Crawford, L. P., Song, P., Fisher, A. C., & Lawrence, N. S. (2015). A novel sensor based on electropolymerized substituted-phenols for pH detection in unbuffered systems. RSC advances, 5(126), 104048-104053. https://doi.org/10.1039/c5ra22595g

This work summarizes the electrochemical response of a range of substituted phenols, including salicylaldehyde and salicylic acid, for use as a voltammetric pH sensor for the determination of pH in both buffered and unbuffered media. Suitable candida... Read More about A novel sensor based on electropolymerized substituted-phenols for pH detection in unbuffered systems.

Rebuttal to the comment on article "poly(3-hydroxybutyrate)-functionalised multi-walled carbon nanotubes/chitosan green nanocomposite membranes and their application in pervaporation" (2015)
Journal Article
Ong, Y. T., Ahmad, A. L., Zein, S. H. S., Sudesh, K., & Tan, S. H. (2016). Rebuttal to the comment on article "poly(3-hydroxybutyrate)-functionalised multi-walled carbon nanotubes/chitosan green nanocomposite membranes and their application in pervaporation". Separation and purification technology, 158, 94-95. https://doi.org/10.1016/j.seppur.2015.11.042

Taylor bubbles at high viscosity ratios: experiments and numerical simulations (2015)
Presentation / Conference Contribution
Hasan, A., Hewakandamby, B., Azzopardi, B., Xie, Z., Pain, C., & Matar, O. (2015, November). Taylor bubbles at high viscosity ratios: experiments and numerical simulations. Presented at 68th Annual Meeting of the APS Division of Fluid Dynamics, USA, Boston

The Taylor bubble is a single long bubble which nearly fills the entire cross section of a liquid-filled circular tube, often occurring in gas-liquid slug flows in many industrial applications, particularly oil and gas production. The objective of th... Read More about Taylor bubbles at high viscosity ratios: experiments and numerical simulations.

Experimental study of interfacial structure of a falling liquid film in a vertical pipe (2015)
Presentation / Conference Contribution
Hasan, A., Azzopardi, B., & Hewakandamby, B. (2015, November). Experimental study of interfacial structure of a falling liquid film in a vertical pipe. Presented at American Physical Society-Fluid Dynamics Fall Meeting

Many studies in the literature provide time series data of the film thickness at one or two points on the pipe wall. Most of these studies focussed on either flat plates or small diameter pipes. The main aim of this paper is to study the characterist... Read More about Experimental study of interfacial structure of a falling liquid film in a vertical pipe.

Selective oxidation of cyclohexene through gold functionalized silica monolith microreactors (2015)
Journal Article
Alotaibi, M. T., Taylor, M. J., Liu, D., Beaumont, S. K., & Kyriakou, G. (2016). Selective oxidation of cyclohexene through gold functionalized silica monolith microreactors. Surface science, 646, 179-185. https://doi.org/10.1016/j.susc.2015.10.039

Two simple, reproducible methods of preparing evenly distributed Au nanoparticle containing mesoporous silica monoliths are investigated. These Au nanoparticle containing monoliths are subsequently investigated as flow reactors for the selective oxid... Read More about Selective oxidation of cyclohexene through gold functionalized silica monolith microreactors.

Characteristics and catalytic properties of Ni/CaAlOₓ catalyst for hydrogen-enriched syngas production from pyrolysis-steam reforming of biomass sawdust (2015)
Journal Article
Chen, F., Wu, C., Dong, L., Vassallo, A., Williams, P. T., & Huang, J. (2016). Characteristics and catalytic properties of Ni/CaAlOₓ catalyst for hydrogen-enriched syngas production from pyrolysis-steam reforming of biomass sawdust. Applied catalysis. B, Environmental, 183, 168-175. https://doi.org/10.1016/j.apcatb.2015.10.028

The production of hydrogen-enriched syngas from the thermo-chemical conversion of biomass was studied using Ni/CaAlOₓ catalysts prepared by co-precipitation method. The effect of Ca addition with different molar ratios of Ca:Al (1:3, 1:2, 1:1, 2:1, 3... Read More about Characteristics and catalytic properties of Ni/CaAlOₓ catalyst for hydrogen-enriched syngas production from pyrolysis-steam reforming of biomass sawdust.

Plasma-photocatalytic conversion of CO₂ at low temperatures: Understanding the synergistic effect of plasma-catalysis (2015)
Journal Article
Mei, D., Zhu, X., Wu, C., Ashford, B., Williams, P. T., & Tu, X. (2016). Plasma-photocatalytic conversion of CO₂ at low temperatures: Understanding the synergistic effect of plasma-catalysis. Applied catalysis. B, Environmental, 182(March), 525-532. https://doi.org/10.1016/j.apcatb.2015.09.052

A coaxial dielectric barrier discharge (DBD) reactor has been developed for plasma-catalytic conversion of pure CO₂ into CO and O₂ at low temperatures (<150 °C) and atmospheric pressure. The effect of specific energy density (SED) on the performance...

Optimization of active muscle force-length models using least squares curve fitting (2015)
Journal Article
Hou, M., & Mohammed, G. A. (2015). Optimization of active muscle force-length models using least squares curve fitting. IEEE transactions on bio-medical engineering / Bio-medical Engineering Group, 63(3), 630-635. https://doi.org/10.1109/TBME.2015.2467169

The objective of this paper is to propose an asymmetric Gaussian function as an alternative to the existing active force-length models, and to optimize this model along with several other existing models by using the least squares curve fitting metho... Read More about Optimization of active muscle force-length models using least squares curve fitting.